A-1ux are confident in the quality of their products. If you need assistance, please contact them. The SMA Male has a voltage of 2.7-5V, a length of 0.1 meters, and a gain of 28dB. Faster gps signals capture, lower power consumption, stronger anti- performance and wider working voltage range are some of the benefits. You can attach it to any metal surface with the magnetic base. The head unit is powered by the power. Recording your speed, location and latitude. The data can be seen in a player. Recording your speed, location and latitude. The data can be seen in a player.
2 in 1 antenna for a gps navigation system module The antenna's center Frequency is L1:1575.42MHz and it has a band width of>9MHz. The 4G LTE Antenna Specification has a Frequency Range of 698960/17102700MHz and a V.S.W.R of 3.0. The cable is 3 meters in length. SMA male is used for mounting Don't worry about security problems. They are willing to provide a 1 month replacement warranty and a 100% satisfaction guarantee for their 4GLTE +GPS Antenna. Please contact their customer support if you get a faulty one.
👤It was well packed and arrived quickly. A bar was added to my reception. I am happy.
It's compatible with the NETGEAR MR1100. The SMA male connection is on the waterproof ActiveGPS antenna. Attach it to the roof of your car with a magnetic base. It has a gain of 28 dB. 3 meters is the length of the cable.
👤I bought a car stereo that I really liked and it came with a gps antenna, but in my SUV I was getting poor gps reception. I downloaded a gps signal app and it showed a small connection to 3 or 4 satellites. I don't think the gps antenna that came with the car stereo was the cause of the terrible reception my phone had. I decided to try this antenna instead of the one that came with my stereo after reading the reviews. Wow, the signal strength to 12 satellites is very strong. The signal improvement was night and day compared to the one I replaced. Couldn't be happier.
👤The products work as they should. I use it with an amateur radio project. I am concerned about the quality of the SMA cable. I already see a loosen of cable when in use, and they are of a cheap stamped crimp build. I had to secure the cable to keep it from moving. I think this is to lightweight of cable for the device and not enough for a proper connection. When the product arrived early, I was concerned that the device would not work or be in one piece. The package had been badly damaged and left concern. I will keep my previous comments after using this gps puck for several months. I have two of them. One for home and one for truck. I have been living in the desert and have been able to test this. It went through a lot of precipitation. It is still working. The magnet is not moving. I am able to see about 17 satellites at most times. This is connected to a radio station. 73, de KF6NFW.
👤I have a cheap gps module and three antennas, but a small ceramic antenna on a roof with a great sky visibility is non-working, and a larger sim39EA antenna that gets a fix within 3-6 minutes outdoors is not always reliable. Within 5 seconds, the module can fix the sats. Absolutely worth it.
👤I need to integrate an external gps antenna into my electrics kit. The cable is long, the antenna is covert, and the magnetic base is nice. The unit was tested in the basement of my house, which is not the best location for gps reception. The antenna had a lock on it. Very impressed! The antenna will not work on its own. You need to connect it to the SMA.
👤This is a good unit. It seems like it would be water resistant. And be strong. Nice SMA connection. Pulls in signals very well. This is not a dual band antenna. Galileo will not be picked up by it. This is not a fault of the unit because it did not pretend to do so. The cost of dual band antennas is high.
👤The SkyTraq Venus838FLPxGPS is working very well, thanks to this antenna. The wire length provided is going to allow me to wrap up the datalogger/lap timer project that I just finished, and I am in the process of mounting this antenna to my motorcycle. I was able to pick up the signal from the inside of the house without any issues. I would recommend this antenna to anyone.
There is no exposed cable in the pierce mount. The right angle SMA connects into tight spaces. The gps antenna is a 1 MHz center Frequency for the USA. The low noise amplifier is compatible with 2.25V DCGPS Receivers. Weatherproof is perfect for external gps antenna for cars, trucks, vans, boats and RV's.
👤The product is useless and unable to be used.
Menu is used to get the data from the gps receiver after instialled U-CENTER V8X. The software can be downloaded from the official website. It's compatible with Win 11/10/ Win 8/. Win 7/Vista/XP/98/CE. The software is free. All-in-view tracking on 56 channels. The U-BLOX 7 Chipset has a Magnetic base, high sensitivity and Strong Singal. Tracking sensitivity is high. IPX4 water resistance, dust-tight, cable length is 6.5 Ft. OpenCPN can be supported on the Raspberry Pi. One year warranty.
👤I was able to get the gps receiver to work with OpenCPN on my cheapo Windows 10 tablets. I plugged the receiver into the port that was provided for it. The driver was installed by Windows 10. I opened the "Option" menu, selected "Connections", and then clicked to look at the available COM ports. In my case, I chose the newCOM7 for me, and chose a buad rate of 9600, which is the same as the standard 4800 default. I clicked "Apply" and voila! The satellite logo in the upper right corner of the screen turned red to green when my boat appeared on the chart. The Ublox program is not needed. The big take-away is that Windows 10 will automatically download the right driver, but it is only for the serial tousb part of the receiver. It shows up on Windows 10 Device Manager as a new COM port, not as a "GPS Receiver" or something similar, but as a new port under the "Ports (COM & LPT)" header. OpenCPN can receive and decode the "GPGSV" and "GPGLL" sentences if the receiver spits them out.
👤I wanted to use Open CPN as a navigation software and install the U-Blox 7 gps sensor. Not this year. The "sensor" is not compatible with Windows 10 without uploading a Virtual Comm Port. On the U-Blox website, they offer the VCP with an.EXE extension, but it is not an exe file, but something called a 10 file. I think you understand the picture. The internet is full of people who are experiencing the same issues. All necessary charts are downloaded and plug-ins are available. If your computer isn'tGPS enabled and you are using OpenCPN, I would suggest you use another antenna. Why 2 stars. I was able to get the software they give to see antenna performance to work, and the lat and lon were correct. I have been trying to work around the difference between a device and a sensor for over four hours. I sent emails to both of them with no response.
👤This device was bought with the intention of cannibalizing it. Attach it to a port and read the output for accuracy. The device I tested used a /dev/cu* device instead of a tty. The time and gps information was accurate. The internal device was in the shell. I had to destroy the shell. There aren't any screws. The RF shield fell off. It had to be re- soldered back on. There are five The Ubx-G7020-KT is the "standard" grade device. The more rugged G7020-KA is not what it is. There is a small battery on the board that can be used for a real time clock. This would allow for quicker signal acquisition. I would expect this device to fail after a few years. I wouldn't recommend this device for harsh environments. The manufacturing process used is flawed and no gasket are used to stop the flow of water. The manufacturing process was not enough to keep the shield in place. There are three The chip is not rated for harsh environments. It was a bargain, but don't trust it if safety or cyber security is ever going to be an issue. The battery was a pleasant surprise, but I wonder why the low end device has this.
Help your gps to get stronger signal by using a waterproof active antenna. It picks up your position quickly with a 28 dB of gain. The magnetic base of the gps antenna can adhere to any metal surface. Pack of 2 has a cable length of 9.84 feet and a SMA male plug. A-1ux are confident in the quality of their products. If you need assistance, please contact them.
👤I used an external SMA connection for my gps receiver and it worked well indoors.
The high gain is 29 dB. The patch antenna is ceramic. Out-of-band is a high rejection. The center frequencies are 1,575 MHz and 10 MHz. The center frequencies are 1,575 MHz and 10 MHz.
👤I'm leaving this review because I'm very happy with this antenna, and because there is so little information in this ad and online. I didn't expect a name-brand THE 304stainless bolts or a polished STAINLESS BRANCH. It looks better in person than it does in the photos. It's meant for a boat. It's not pictured, but my rubber boot covered the connector. It seems to be perfectly accurate to pick up satellites quickly indoors. The generic plastic sticky-back antennas are a bit more expensive. Unlike a sticky-back antenna, this Tram antenna will be easy to mount and route. The bolts are long. You'll probably want to replace the hardware or cut the bolts if you're mounting to a 7/8" rail. It looks as though the brackets could fit the rail, but they will hit the cable before the full length of the bolts can be used. There is no reason for the bolts to be this long. It's a good thing.
The outlet terminal is compatible with the I2C port and the serial port of the APM flight control. Plug and play other flight controllers are also available. The U-B-LOX M8030 KT has a built-in TCXO which maintains good consistency in the temperature of -40 C +85 C. You can use the desire of one module in many ways. SBAS assistance, auto-positioning, auxiliary positioning, drift, and timing accuracy are included. Three in one function: support gps bsd dual-mode positioning, plus compass chip. You can use the desire of one module in many ways.
👤I asked if there was a command to change the update rate from the default 1hz to 10hz. There is no comment from the datasheet. It is hard to understand the reply from the seller, "You need to setting 10hz does not support all statements." I reached out to the manufacturer of the module by writing an email. The customer service of the company in Shenzhen is amazing. One of their engineers taught me how to change the setting from u-center to the module, and how to send a HEX array to the module to change the update rate and baud rate. I posted an image that works for me. If you don't want to work on the gps module via the arbian or pi, you need a serial-usb tool to connect the gps module to your computer. I have this module work at 115200 baud rate and 10hz update rate. Hope it works for you as well. If you can't change it, leave a comment.
👤Never got it to work. This version is the one I replace the BN 220 with. It lights up, but not by Betaflight. I had no issues with the other version of the gps module receiver. I put that one in a matek wing board because it has wire from the gps module to the antenna, which is not the best fit for a drone. I tried it again, but no luck. It gets power but is not recognized by the FC. Remove the solder joints for the gps and then solder another one to it. I had high hopes for his one, because of the size of the antenna. This is the second one I bought. The first time I sent it back, the antenna looked like it had been scratched, and it was shipped with no cables. If you have a room, then the better deal is the navigation satellite positioning module receiver, which has solder pads and works.
👤Using a computer to connect to a Pi. It works if you wired it up. I used the U-Blox U-Center software. I was surprised to find a 3D lock on my desk. I was able to make some changes using U-Center. This is being used for a radio project. It works great on Linux.
👤Is small at 1.820"dia. It worked well on my 1400mm fixed wing. I used the supplied two-sided tape. I mounted it and the flight controller to get the best accuracy. A good buy at half the price.
👤Our RC truck has a gps unit. We are using it for a device.
👤It is easy to connect to my antenna tracker.
👤It works well for my needs. Even without the best view of the sky, it gives me the accurate speed output I was looking for.
The Frequency is 1575.42MHz. The SMA Male Straight Connector has a feature: Adhesive mounting, gain of 282dBi, and cable length of 3m. The package includes an antenna x 1. It's compatible with cars and trucks made by Ford, GM, Chevy, Dodge, Cadillac, Lincoln, BMW, Mercedes Benz, Volkswagen, and VW. The Ford F-Series F-150 Raptor and the Ford F-150 are compatible with the factory navigation system head unit. Super Duty, Ford Edge, Escape, Explorer, Focus, and 2010-2020 Ford Fusion, Mustang, and Taurus are compatible with GM and Chevrolet trucks and cars that have built-in factory navigation system head units. It is compatible with the Dodge Ram 1500, 2500, 3500 and Dodge Avenger. 3.0 meters is the length of the cable.
👤It fits. My. There is a radio. It was perfect. Performance is. Great.
The power brick mini and cable set are included. Help your gps to get a stronger signal. Picks up your position quickly. The antenna has a magnetic base which can adhere to any metal surface. Ready to use. The main unit is 45 x39 x 13mm.
👤Many modules come with tiny chip antennas, but these work better than that. Within a few minutes, I picked up dozens of satellites.
👤It was much better than the one that came with my stereo headunit. When the car was parked outside, the original barely got signal. It picks up 12 satellite's and stays in the 40's.
👤The vendor replaced my product after it expired. Hats off to the product, it works on 3 different units.
The package includes a male and female cable. The V.S.W.R is 2.0 and the LNA Gain is 28. The antenna extension cable is called the RG174 3M/ 9.8Ft. Fakra c blue female right angle; Size: 1.77"x1.42"x0.55; package includes 1 pc Fakra gps antenna. Excellent temperature stability, low noise figure, and a strong magnetic base are features. VW works for the following models: Golf 5, Golf Plus, Touran, Touareg, T5 Multivan, RNS300 310, RNS315, and RNS500. Works for Chrysler:RB3; Becker:RB3; and MMI DVD 2G,3G,BNS low line.
👤Works on Harley Boom! 6.5 GT radios! Look no further.
👤Works well for my harley installation.
👤I bought the RNS-315 unit because my car didn't come with gps, but the dealership wanted me to take apart my roof liner and install an antenna there, and they gave me a quote of $300. I put the antenna on the side of my dashboard corner with some double sided tape after plugging it into RNS-315. I didn't have to have my headliners taken apart.
👤Every startup had a navigation fault message. Only about 75% of the time is accurate. Another unit that works 100% of the time was bought. I'm going to return both and buy a new one, though I'm not really happy with the performance.
👤I tried removing the bottom sticker to allow the magnet to touch the metal, but it didn't work. The larger metal plate didn't fix the problem.
👤I upgraded to a sync 3 system in my Ford Flex and the clock wouldn't change, it just reset to the incorrect time when I tried to adjust hour/minutes. Within a few minutes of starting up the vehicle, I was able to reset the clock on the back of the unit. And it showed correctly. I can now manually adjust the clock. Highly recommended!
👤I used this antenna to upgrade my car. After trying another antenna that gave a fault every time I started the car, I swapped to this one and I have no more issues. There is a The blue Fakra connector has a rotating wire connection at the back that allowed me to route the wire over the obstacles in my car.
👤So far, so good. The piece of junk antenna that came with the Ford F-150 sync 2 to sync 3 conversion was replaced. The problem with the time change on the unit seems to have been solved. It was mounted with strong double sided tape.
Gps module sma products from Uxcell. In this article about gps module sma you can see why people choose the product. Superbat and Qgp Supply are also good brands to look for when you are finding gps module sma.
Uxcell, Superbat and Qgp Supply are some of the best brands that chosen by people for gps module sma. Find the detail in this article. Proxicast, Vfan and A-1ux are also brands that their products are worth to check.