Best Gps Accessories Dash Mount Tom Tom

Accessories 3 Feb 2023 10+ Comments Open

1. Windshield Dashboard TomTom EasyPort Pattern

Windshield Dashboard TomTom EasyPort Pattern

The EasyPort mount pattern is used for the TomTom gps. It works well in hot climates and can be attached with a touch lever. Also mounts to the dashboard with a disk. The standard is clear suction.

Brand: Arkon

👤The replacement mount is very good. The mount that it came with was the only thing that I didn't like about it. I always supported the unit from behind with my fingers when using the original mount, so that it wouldn't fall off or slip to a bad viewing angle. It was awkward to attach the gps to the original mount. It took a bit of force, and I had to double-check that it was secure before I let go of it. I learned that it hadn't snapped on when it fell off the mount. I got a third-party replacement for my original mount, which was basically a copy of the original. The mount shook like crazy as I drove, the cup couldn't stand the heat on sunny days, and it became useless after a few months. I saw the Arkon mount on Amazon and decided to try it out. It was easy to install on my car, and unlike the original mount, this one feels solid. I don't feel like I'm going to mess anything up because the mount provides enough support from behind that I don't feel like I need to. No more tapping with my thumb. The mount is solid, and I think it's what the original mount should have been. I wish I had found this a long time ago, but even though the gps is no longer supported by the company, I feel like I'm using an upgraded device. I will definitely change this review if it doesn't work out. I think it's a good idea based on my experience so far. I'm not sure if there will be any more map updates for the XXL 540 because of the fact that it will no longer be supported by TomTom. The device should be useful for quite a while since it was updated in August 2019.

👤I replaced my mount twice. After a couple of years, the cup tore, and I had to replace it, because it fell off the window frequently. I was looking for a replacement and found this one. The locking mechanism is good. After a few small adjustments, my car was in the perfect position. The heavy device does not shake or vibrate as I drive. The mount was in place all winter. It came loose in the spring. It was easy to re-mount the cup again. Just what I needed.

👤A mount that holds the gps firmly and doesn't let it fall is finally here. When using the original mount, my XXL540 would fall off the dash mount. I used a rental car and bought this for my trip. If you want to use their gps service, the rental car companies charge an insane amount. I fastened my gps to the mount on the car. It held the navigation device for my entire trip. When it was time to return the rental car, it was easy to release. The mount is strong and holds the mount and the gps firmly. * It can be adjusted to any angle. * The gps has minimal vibration and handles bumps well once the mount is tightened. Couldn't find any.

2. APPS2Car Dashboard Friction Magellan Smartphones

APPS2Car Dashboard Friction Magellan Smartphones

The spring lock holder will fit any 3-7 inch gps and cell phones with a unique Anti-slip Jello Block under the mount that will stick on to your dashboard and be easy to clean with water. The device stays on the dash with the help of the weighted body and anti-slip bottom. The APPS2Car Beanbag Mount is easy to attach a gps / cell phone unit to your car, and five slots allow you to adjust your device in multiple angles. One of the best alternatives to mount a car on a truck is to use a cell phone. No cradle needed! No magnets, no harm to your device! The heat made the cup fall off. There is no interference with the air conditioner or the cd player. The Nuvi 1100 1200 is compatible with the portable Friction Mount. etc There is a car mount for all of the phones, including the Note 10 9 and the S10e S9 S8 Note 9. Start 45 55 60 65 500 600 Via 1405 1435 1535 1605 1635 XXL 540 330 350.

Brand: Apps2car

👤This would be a good design for a gps holder. This thing does not stay put. I quote: " Find your sweet spot and put down the sticker, then put the unit on it." The thing will become airborne after you take a 2 mph turn.

👤I have been using this for over two years. It holds my car. I drive a 2500HD. I've never had it move. Some of the reviews say that theirs moves around, but I drive around construction sites and roll down the highway, and it has always stayed in place. I'm very happy with this. I don't move my device. On hot sunny days, the mount would fall off.

👤One needs to keep a clear view of the road ahead and to obviate the vacuum holding your gps to a windshield from failing and dropping in traffic and/or repeatedly. It is easy to move in traffic. There is a It's best to wait a while, maybe forever, from sticking it to one spot on the dash or console. You will want to take it with you to another vehicle occasionally, but you will want to change it from time to time.

👤The issues that I had with this Mount may be different to what I've had before. Is it ok for other gps models? The power cord must be connected to use the traffic detector feature of the 2455. The power switch is located at the lop left of the unit and the power cord is located at the bottom left. To allow for minimum clearance between the plug and the grip "tooth" of theGPS Mount while providing access to theGPS power switch, theGPS must be shifted to one side. The grip on the opposite side of the mount does not provide a secure grip to the gps. Photoe 3. Issue #2. There is a non-stick gel substance at the bottom of the gps mount. The bottom surface of the Mount is flat. It was difficult to find a flat surface for the non-slip gel to grip on the front console of my vehicles. A better design would have been a flexible bottom surface. As dust accumulates on the substance, gel-type non-stick substances lose their effectiveness. Positives. The design is easy to store and may be a good mount for many gps, but not for a garmin. The concept is ok, but a few changes away from an excellent gps mount design.

👤I've used this to hold my electronics. It holds both securely. I need to wash the sticky area on the bottom of the mount to remove the dust after the mount slides a bit. It is guaranteed to elicit further security screening when I take it with me when I fly and rent a car. If you want to keep your luggage and carry-on bag free of TSA, you should put it in a screening bin. They can't see through it, so it gets swabbed.

👤I wanted a holder that wouldn't require me to block an a/c vent, so I chose this one. It was easy to figure out because it works like a giant clothes pin and the gps sits securely in the ridged "mouth". It's weighted with a non-slip bottom that's about the size of my open hand, so it doesn't slip when placed on the dash. I didn't want to use the peel-and-stick pad that was on the bottom. I would rather have the option of taking the gps off the dash when it's not being used, and not leaving a sticky glue mess. It's what I needed since the windshield cup on my old gps didn't fit well.

3. BOROLA Tomtom Holder Window Suction

BOROLA Tomtom Holder Window Suction

The plastic is very durable and strong. In hot climates, the Windshield Suction performs well and is easy to attach with a one-touch lever. It's easy to install a replacement for your device. Don't lose your way! This mount will keep your Nuvi gps with you at all times. Attach the mount to your car with the help of a cup. It's compatible with the following: One 125, One 125 SE, One 130, One 140, and the XL V2.

Brand: Borola

👤The ring on the twist mount does not hold the device well, so I replaced it with the original one, which still held the device well. It is easy to replace the mini-philips screws.

👤The mount sticks to the glass. The leaver makes it a lot easier to take on and off, and the glass makes it easier to see, unlike the original Tom Tom mounting. The only complaint I have is that the gps will pop out of the ring mount very easily.

👤It works well. Better than the original Tom Tom stand.

👤I was looking for a replacement for a six year old device. I found it on Amazon. It holds my device better than the dashboard one that came with it. Happy with the purchase.

👤The device will fall off the window when the holes are not being used. The device will fall off at a rapid rate.

👤The ring was poorly designed. Does not hold onto it securely. No matter what you do, the TomTom falls off.

👤Pratique, car facile installer, reste pas collée trs longtemps. J'ai acheté, la mme chose. Mme satis fait, J'en suis quand.

👤I bought this for my older Tom. The cup is very strong. A good deal!

👤It has been said in the head line.

👤It's not the strongest magnetic grip, but it's worth it for the price.

4. GPS Mount Cell Phone Holder LUXMO Universal Smartphones

GPS Mount Cell Phone Holder LUXMO Universal Smartphones

This car mount is compatible with many gps devices, such as the iPad mini, the phone, and the Yoga Tab 3. Also, the S10/S10 Plus, S8/S8 Plus, Note 8/S7/S6, V30/V20, and thePixel XL are included. The Sticky Non-Slip Base adhere to the flat dashboard with a strong grip. Stable even on a bumpy road. Ensure that the driving is smooth without worrying about the gps holder falling down. If you keep your phone/GPS in front of your eyes, it will not bring visual blind spots and you will be able to drive safely. Different devices and flexible angles can be achieved with three slots design. You can wash the gel pad if you feel a decrease in stickiness after a long period of use. If you feel that the mount is not stable, you can use the 3M sticker to fix it. Four actions are needed to finish it. Remove the transparent film from the dashboard and put the holder in the upper clamp. The rubber clip and rubber gel pad are soft and will not hurt the dashboard.

Brand: Luxmo Luxury Mobile

👤I tried to hold the screen of my back-up monitor on two other systems. My car is a Genesis and I live in the Central Valley of California. The cup kept falling off when it was warm. It's not great to find a monitor on the floor. The kind for my cup holder was too far back. The Genesis does not allow use of the air vents. This one works. There are no issues and it's also replaceable. I can use this for add-on on my new car.

👤The phone holder is very stable. I wanted to switch between those two items as needed. It's closed and flat when not in use. It's mounted on a rubbery pad. I didn't use the enclosed sticky tab. I like that I don't have to glue it down, it just grips on its own.

👤This was bought to use as a gps device for a long road trip. It has held up well on the dash of our car. It's great so far, but I can't speak to longevity.

👤I bought this dash mount holder for my new car. I was worried that the mount would fall, but it didn't. Since December, I have left it on my car. I don't know if it would still be secure if I had removed it.

👤We bought this device to hold our large device on the dashboard. It was advertised that it could hold larger devices. When you get it out of the box, it works well. It opens up a pair of jaws and holds the gps between the teeth. It is difficult to hold a larger device because it has to open up very wide. There is not enough clearance between the dash and the windshield for the wide-open gps mount to fit. The device is fine, but we had to return it because it wasn't able to perform the function we purchased it for.

👤The holding power for the tablets is not good and needs to be tightened so it holds better.

👤I bought something else because the Tablet didn't fit. It may work for others.

👤It's a good idea to prefer over windshield cup holders. It's never necessary to be adjusted. I keep the gps in the car. It was difficult to remove the gps.

5. AmazonBasics Dashboard Magellan Portable Navigators

AmazonBasics Dashboard Magellan Portable Navigators

Attach a gps unit to your dash with the Amazon BasicsGPS Dashboard Mount. The bottom of the gps mount is anti-slip. The mount can be used on most car dashboards. It is necessary to hold the gps in place. All window mounts are compatible with the Amazon Basics 1-year limited warranty.

Brand: Amazon Basics

👤There is a sticky silicone disk at the center of the mount, but it is not clear from the description. The disk is covered with a film. The mount will slide on the dash if you leave the protective film in place. If you remove the protective film, you expose a sticky surface that is designed to adhere the mount to the dash. Not what I wanted. I removed the silicone disk. It took a bit of effort, but it came off without a hitch. The mount doesn't slide around when the disk is removed, and the bottom of the mount makes contact with my dash. I thought I was buying the mount in the first place.

👤The price was good, but it was on the dashboard. They need to make it better. It won't stay in place. This could be better than Amazon trying to make their own brands. Who wants navigation to fall off the dash on simple turns?

👤99% of modern dash material is textured dashes, which is why the suction cup dash mount for the cameras from GoPro doesn't adhere to them. I needed an alternative for my low recording car camera. The bean bag gps mount is an excellent alternative. Within 24 hours, the base holder was cured and attached to the dash mount. There are negative comments about the mount. This wasn't an issue. The device has three heavy bean bag arms with two cellophane covers on the bases, just peel them off. I cleaned the base with alcohol and dried it to make sure the camera holder was attached perfectly. The bottom-side of the mount that goes on top of your car is sticky once you remove the cellophane. I use a lint roller to remove debris. The cool thing? I can just pick up my camera and move it to any other car I want. If it works for my camera, it will work for the original intended use of the device. I don't have any complaints.

👤I love this! It keeps the gps in place. I had issues with the gps falling on the floor when it got stuck from the window. The heat in the car is a problem for me. I had an issue with the gps coming off and falling to the floor, but the stay put on the dash does not slide. I had to put double sided tape on the gps to keep it from coming off but it was not due to the mount but the heat.

👤After I removed the plastic film, it's sticking very well and I'm very happy with my purchase.

👤I thought the Amazon car dashboard mount was a great solution to avoid putting sticky pads on my car dashboard, since I bought a nice phone holder. The anti-slip bottom doesn't work well, and the mount is not a friction mount. There are any mounts you want to attach to it. The price is affordable. The product looks like a mount, but it's not. There is a sticky silicone disk in the center of the mount. You need to remove the protective film. There is a The bottom doesn't work well. I was driving and the mount slid around on my dashboard. I didn't remove the protection film on the sticky silicone disk because I don't want to have sticky marks on my car. There is a The weight of the Amazon dashboard mount is not heavy enough to hold the mounts, so they can't be too heavy or long. The dashboard mount tilted even if I used the sticky pad on the bottom of the phone holder. I decided to buy a portable friction mount from a company that is heavier than the one on Amazon. It's more expensive than the Amazon one. It's a truly friction mount, and the anti-slip bottom works well. I can put it on a non-flat surface.

6. HapGo Universal Smartphone Dashboard Smartphones

HapGo Universal Smartphone Dashboard Smartphones

The personalized car mount will definitely stand out among the common ones, because of the crocodile skin and green eyes. The rubber base and crocodile teeth give stable support to prevent your mobile devices from being crashed. The device type that is suitable is garmin Nuvi, Via GO, and other 3-6 inch devices. It's an ideal gift choice to put it in your car. A unique design added more scores. HapGo Team is confident to give you a quality lifetime warranty.

Brand: Hapgo

👤Just got this. The "Croc" was installed without a problem. I think it is filled with sand rather than beans. There is a section in the rear that is made of silicone. I went over the area where I was going to install the croc with rubbing alcohol to remove any leftover grease. I put the croc after removing the film covering the sticky section. It's important to remove grease and oil from the area where the sticky silicone will rest. I used my gps to drive around for a couple of hours. The croc never moved despite the heavy gps. It works better if you have the suction cup holder with you. It adds a little personality to the vehicle.

👤The plastic spring broke after six months. I didn't get a warranty as stated in the description. Contact manufacturer for warranty. The manufacturer said that Amazon doesn't provide a link to this. You can find warranty information on the manufacturer's website.

👤I like this thing. The phone is held nice and tight. I didn't need to adhere to it because it fit in the top tray of my truck and is stable. This is what you want if you like alligator/crocodile stuff and need a phone holder.

👤The phone holder is perfect. Even without the sticky part, it stays put. I was in the Everglades and in some rough terrain, my gator head never fell off my dash, I wasn't even using the sticky part. It holds my phone in two different ways, vertically and horizontally. I photograph nature. The fact that it's a gator head was an added bonus. This holder is recommended by me. There is an update 11-4-20. The holder doesn't fit my car. It's a shame. I cleaned it up and it is now sitting on my desk as a phone stand.

👤Will not stick to dash and only has one small sticker to keep the whole thing anchored. It's lost its stickiness very quickly.

👤I bought this holder for my father, and it is very easy to use. Thejaws open and close on either a cell phone or gps. The holder has enough weight to keep it from sliding around the dash while driving, even without using the included strip. This product is very good. It is cute.

👤I just got a neat gps holder. It is very sturdy and holds my device very snug. No more people falling on the floorboard. Under normal driving conditions, it does not slide on the dash. It was very pkeased and may order more for gifts.

👤I have yet to use it because it's sliding on my dash empty. I tried the old hot glue trick, but it didn't stick to it. Money was wasted.

👤Put large screws in place.

7. Garmin Accessories Bracket Cradle Mount

Garmin Accessories Bracket Cradle Mount

SoeKoa is a brand. The SoeKoa logo is on all of their product packaging. If you receive a product with the SoeKoa logo, please request a refund and make a complaint to Amazom. Only the following models are applicable to this product. The 17mm ball sockets are high quality. The design is lightweight and exquisite. Attach Nuvi to the suction cup holder, portable friction bracket or shirless instrument panel brackets using their brackets mounting. It's compatible with the Nuvi. 52LM 54 54LM 55 55LMT 56LMT 2457LMT 2497LMT 2577LT

Brand: Soekoa

👤The screen on the RV770 fell off when we traveled across the country. The display would fall off if the mount was not holding it. I thought I would have to glue the ball mount to the bean bag mount. I was surprised that it was hard to get the ball in and then a very secure connection. I'm happy to be here for the rest of the trip. If you have a gps that can come off and you have the original brackets, these are awesome.

👤It's a shame that this isn't an own part anymore. This part isn't quite right. It's difficult to fit it on the ball because it's too small. I had to use oil to get it on and force it so hard that the metal ring came out. The gps does not "snap" on after all that.

👤This is a good value for the money, even though it is not a genuine part. If you are willing to do a little sanding or filing, it will work. It's not as polished as the original. It has some ruff edges. It took less than five minutes to clean it up so it wasn't tight to fit. I don't think the part is worth twice the price. I prefer the older mounts but they don't work with the new gps design. I'm guessing these won't last more than 3 years. When I need more, I will buy again. They arrived a few days after the order was placed. I can use my gps right away. Thanks.

👤The product is similar to the original one. I have not been able to use it yet because I need a piece of furniture. Prime shipping has no guarantee. The product I ordered and the one I received were supposed to have 2 days. I'm still waiting for the piece to arrive, it took 10 days. This is an issue with Amazon. I choose a vendor on prime who claims 2 days when I need something quickly and often pay more for it. If not shipped, Amazon should back their guarantee with something more. I'm buying more from Ebay because of this.

👤Quality is the reason why these are returned. The gps ball mount has a spring that tries to pop out. The tab that slides into the gps at the top is cast too thick and does not fit into the gps without being forced. I still have a part that works, but these are a flop because I ordered the real part at the same time. I can see using a $3 and having to force it together and break a $400 gps, no thanks.

👤It popped off when I tried to keep it on the back of the unit. I was going to break the unit if it stayed on because I wanted to get it on the ball. Got them today and will return them tomorrow.

👤I wonder if there is a place where Chinese cheap generic parts manufacturers can find good quality parts, if they want them really cheap. The part doesn't fit on the original hook. It looks like it will break into pieces the first time you open it. I am sending it back from where it came from.

8. Yonisun Suction Holder Windscreen Windshield

Yonisun Suction Holder Windscreen Windshield

Don't lose your way! This mount will keep your Nuvi gps with you at all times. Attach the mount to your car with the help of a cup. Extra gps mounts are a great solution for moving your navigation system from one vehicle to another with less hassle. The mount is not included.

Brand: Eeejumpe

👤There is an update. Under the Vegas heat, the Suction mount's efficacy failed at the 2-year mark. I didn't see BestDealUSA or Yonisun listed as brands anymore. Semson is still a seller, but it doesn't fulfill by Amazon, so there's added shipping costs. I decided to pay twice-the-price for the item and buy it from Amazon. The larger one is designed to provide extra-holding-power for the larger models. I have ordered off this page, but the large feels more solid and Sturdy than the regular ones. The box was an original one from Garmin. The ball is tight. The actual diameter of the actual swivel ball is 17.2mm. I'm pretty sure I have a good feeling about this one. The original review was not a good one. The mount I bought here is working perfectly after several weeks. The seller was Semsons and the brand was Yonisun. It is still very hot in Vegas. I bought a new mount on Amazon in July of 2016 from this very URL. The seller was Semsons and the mount was called BestDealUSA. It failed under the heat of Vegas. I will not complain about the two years of life for a $5 mount. Solid suction was held 100% of the time until it failed. I got my money's worth. I have learned over the years that these mounts are very susceptible to heat, and that the least amount of warping from heat causes them to be unable to hold good suction. Some are built better than others, and some hold better and last longer. None of the third-party mounts I've ordered have come with any packaging or maker's marks that would prove a specific brand or manufacturer. Who knows what brand of mount is being sold? I don't believe that all these third-party sellers are selling the same mount. Some of them are being rated as working well because other raters are reporting the product as failing after a week. I ordered a similar mount from the same seller that I ordered the previous one from, in order to try and get a better one. I was wondering if the seller would still be pushing old stock under the new brand name. Maybe that seller has higher standards for the product it sells. Or whatever. I don't know if it helped or not. I'm holding tightly and consistently, despite other reviewers saying their mount was not good. There is aSIDE. I have found that the best way to mount the mount to the car is to use a Silicone Sealant like the one I have found from Permatex Clear RTV. You can get it at most auto hardware stores. It doesn't work well because of too much, too little. With the Goldilock amount applied, it improves the hold and endurance of the cup. When the cup fails, it's a chore to clean the windshield. That is usually under summer heat. Most of it will peel off easily, but the rest requires a lot of work. I don't fool with it anymore. If you get desperate, I suggest you try that.

9. Dashboard Mounting Universal Adhesive Diameter

Dashboard Mounting Universal Adhesive Diameter

3M Sticky Tapes can be upgraded to provide smooth, glass-like surfaces for car mounts. 3M PE foam can be fixed on textured surfaces. It is applicable to most suction cup gps/ mobile holders. There are no tools required for installation. Every APPS2Car product has life time customer service.

Brand: Apps2car

👤The dashboard pad is separated from the sticky pad in the heat, so it's placed on my dash. This is not extreme because it is San Diego heat. The 3M sticky pad came from the dash, but the suction pad came from the sticky pad. It works well for suction cup mounts on surfaces where the cup won't fit.

👤The Iottie Suction Cup Phone Mount requires 3 pack of dashboard mounting disks. The product is made of plastic. I put the first one on and it split in a month. The plastic disk separates from the glue on the dash. Within a month, I put the second one on. I put the third one on and it lasted about 6 months and then split apart. I didn't see any reviews that described the kind of failure that I experienced, despite the fact that a number of people said that the glue failed to stick to their dash in hot weather.

👤The dash mounting pads offer an excellent solution to mounting a cell phone mount onto a vehicle. It should hold an average sized phone. Make sure to follow the instructions and clean the dashboard surface where you are going to mount it. If you want to install the pad on a hot dashboard that has been exposed to the sun, be careful as it will not allow enough bonding since the heat from the surface of the dash will still be emitting heat. If possible, place the vehicle early in the day or in an area that has not been exposed to the sun. The cure time is three hours, but I would recommend waiting at least five hours before placing the cellphone mounting device since the cup will attach to it.

👤The cups are very easy to stick to and hold on to, and the backing on the disc is very strong. I used one on my bathroom wall to mount a mirror for shaving, and the second one I tried to use on my car, but it didn't work out. I mounted a phone holder on my car for a few days, but on the third day it fell off, it was a sunny day with a high of 75 degrees, and I was 2 hours into my drive. The only good news is that it came off cleanly, so there was no trace of glue, but the back of the disc has lost its ability to stick, so it is useless now. I thought about trying to remount my phone cradle with the third and final disc on the dash. The third disc will fail the same way the other one did, so I will just blow it up. If you are buying this for use inside your car or truck, don't waste your money, but if you are getting it to use inside the home or office, it's great.

👤I didn't follow the directions on the first two, but on the third I let it set for a week before I tried to mount my phone holder, and as soon as I put it on it pulled the pad off. I used the cleaning pads and it failed. The iOttie's pad worked but I had to remove it to remount it. The original pad was more flexible and could conform to different surfaces. The 3M type tape was not able to hold it's substance.

10. Dashboard Beanbag DriveAssist DriveSmart DriveLuxe

Dashboard Beanbag DriveAssist DriveSmart DriveLuxe

Taiwan is the country of origin. High quality manufacturing. The anti slip base is for grip. Every mount has a smooth Mount Pad. Weighted beanbag stops sliding on corners, so you can Mount your Sat Nav without leaving Tell Tale Ring On Windscreen. Only suitable for the 5 inch models, not the larger sizes which have a larger cup. Only suitable for the 5 inch models, not the larger sizes which have a larger cup.

Brand: Digicharge

👤This is a weighted bean-bag. The material on the bottom is slippery. It's not supposed to do the specific thing. Unless your dash is cloth, it's worthless. The bean-bag mount I bought from my company works great. I wanted to save money and use this one. Wrong!

👤The Nuvi stuck to the windshield with a cup. It would sometimes fall off on long drives. The dashboard mount works well. The bottom of my window mount doesn't move when it's on top of the dashboard, because the cup sticks very well. The adjustment allows us to point the screen in a certain direction. If you also have problems with the mount, I recommend this product.

👤The products pad is not big enough for the RV 890, so I bought this. It's too big for a vacuum. I bought a new one that works well. The one I am using is the Amazon Basics, which is a car dashboard mount. Navigators are available at www.amazon.com.

👤I needed something to take down when I wasn't using, and I hated the ring on the window. I use it for my back up camera monitor when I pull my travel trailer. It does not sit in the tray on a 2020 F-150. Since it is in the dash, it does not move, so I can't comment on that. It's a great alternative to leave a ring on the car when you only use it a few times a month.

👤This holds my Dash camera in place. I don't understand why dash cam are called Dash cam when they are made to stick on a window. I also have a backup camera for my trailer. There are no circles from the cups.

👤Soon to say. But. It may slide around while driving due to the slick bottom. I like that it is heavy and my cup fits perfectly. It should work for me.

👤The product is great at a good price. Very happy. There is a The white tissue paper should be removed for those who are having problems with it sliding. I bet your slide problem is solved once you've done that.

👤It's perfect for the monitor of my camera. I don't need the monitor so I can easily remove it from my dash.

👤This rating was used by me because I found it to be okay. The product was not as good as I thought it would be. I thought the holder fitted all models of cars. The holder on my car is not right and it slides when I corner. I don't think this product is a good one, I think other products with the same function would be better. William Shepherd is a man.

👤Slips all over the place have had to be controlled with two blobs of Blutac.

👤I can sometimes slide when going round corners.

👤It fits on the dashboard of my Honda and doesn't move.

👤Really pleased with the product. Sturdy practical works well.

11. APPS2Car Windshield DriveSmart DriveassistRV StreetPilot

APPS2Car Windshield DriveSmart DriveassistRV StreetPilot

This ball mount is not compatible with RV 890. Extra long gout arm. The aluminum long arm can bend up to 13 inches for various visual angles to your liking, making it easy to mount the gps on the dashboard without blocking the field of view. The gps dash mount is made of a sticky gel and a locking lever that will not come undone or slip off, and you can easily mount it on most flat surfaces. The anti-shake stabilizer is held in place by the strong sticky cup ball mount. A replacement gps holder is an alternative to gps air vent mount holder, gps friction beanbag mount holder and gps dash pad. The fit for Drivesmart 50 is wide. RV 660 760 770 (LMT LMT-S), Nuvi cam, and Zumo are all part of the LMT NA. The StreetPilot DriveLuxe Aera DriveRrack series is one of them.

Brand: Apps2car

👤The unit is not compatible with the RV. The mount is too small. Unless there is a change out ball for the mount, the unit will have to be returned.

👤I bought this as a replacement for a previous design that was mounted directly to the windshield with a short, rigid extension. The new version has a longer "gooseneck" and a better cup that grips like a vise. My initial impressions are that it will hold up, but it's not certain if it will hold up to the constant vibration and sunlight that weaken mounts over time. If you don't need the reach of the previous version, the gooseneck may be a better choice. I quickly realized that mounting my gps to the fully extended gooseneck without thestabilizer was not a good idea. At the end of the "stalk," my gps swayed and jiggled at the bumps in the road. I didn't think there was a risk of it coming loose, but the bouncing was very distracting. In my preferred mounting location, there isn't a good place to add the stabilizer, so I looked for another location where I could brace the gooseneck or the gps against something solid. I put the gps on top of the dash and mounted it directly in front of my driving position. The two points of stability provided by this may not be the best solution for safety reasons. It's helpful to have the gps positioned so close to the controls. Having a constantly moving display right in my line of sight is not good. I think the previous version was better for my needs, even though I may get used to it in time. It was long enough to keep the gps within easy reach, but off to the side where it didn't compete for my attention. I may try to figure out a way to move the mount back to the side with the bracing.

👤My car is a Chrysler Town and Country. I need a long mounting device to be used in my day-to-day driving with my gps device. Your product is very sturdy. The mounting attachment on my Garmin model should work fine even though it isn't listed in the product description. I noticed that the mounting ball doesn't snap into the back of my Garmin nearly as securely as the stanchion that comes with the typical auto units. I'm not sure if it's a problem yet, but I'm sure a good bounce in the water here in Michigan will knock it off the mount. It has solved my issue with locating my gps device. This mount has long-reach, exaggerated sloped windshields.

👤It's a great gps holder. It holds my gps very well. The ball fits well to the gps sockets and the suction is very strong. It does not come with brackets, so I give it 4 stars. If you need brackets to hold your phone, you're out of luck because it doesn't include them with it. You have to look for a different model. I only need it to hold my 7 inch gps and I am very happy with it.

Summary

What is the best product for gps accessories dash mount tom tom?

Gps accessories dash mount tom tom products from Arkon. In this article about gps accessories dash mount tom tom you can see why people choose the product. Apps2car and Borola are also good brands to look for when you are finding gps accessories dash mount tom tom.

What are the best brands for gps accessories dash mount tom tom?

Arkon, Apps2car and Borola are some of the best brands that chosen by people for gps accessories dash mount tom tom. Find the detail in this article. Luxmo Luxury Mobile, Amazon Basics and Hapgo are also brands that their products are worth to check.

You May Like

Share Your Story

Your name:
Choose product to comment:
Write your review:
By submitting this review, you are agree that:
  • Your review is based on fact, honest, polite and not harmful to anyone or any brands.
  • We have full right to show or not-to-show your review after moderation.
  • No spamm please :)
Disclaimer
We might earn comission for your shopping via our links, it doesn't cost you extra. This website is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com