Best Bu-353s4 Usb Gps Receiver

Receiver 27 Jun 2022 10+ Comments Open

1. Dual Electronics XGPS160 Multipurpose Augmentation

Dual Electronics XGPS160 Multipurpose Augmentation

The wide area augmentation system allows your device to connect to several satellites and provide accurate and reliable gps coordinates within 2.5m, Max Speed of 1,150 mph and Max Altitude of 65,600 ft. You can greatly strengthen your gps signal on any device by connecting to it via the gps wireless network via the gps wireless network via the gps wireless network via the gps wireless network via the gps wireless network via the gps wireless network via the gps wireless network via the gps wireless network via the gps wireless Hundreds of applications can be added to your device if you can add accurateGPS to it. The battery life of the gps receiver is extended to 10 hours of continuous use and it comes with a charging cord, a strap and a non-slip pad. The 1 year warranty has high quality and reliability with hassle-free parts and excellent customer service. The dimensions are 2.24” W x 2.24” D x 0.75” H. The battery can be charged in 3 hours. Plug in to 12Volts of direct current source for continuous use.

Brand: Dual Electronics

👤I've been on my third unit since November. The first unit bricked after six months of ownership. After a few months, the replacement unit stopped charging more than 50%. The third unit will no longer be seen by any apps even if the iPhone connects successfully. What is the solution to dual? Wait for an update. A piece of hardware that worked before with multiple apps and no longer works with any of them is going to be fixed by a single app update. I'm not holding my breath. There was an update on February 27th. My third device has failed but will not be covered by a warranty. Two years ago. They don't stand behind their products because of a serious quality control issue. I wouldn't recommend this gps.

👤They managed to have a high review rate on this product. There were more than 4 stars on its page. The usage experience is terrible. It can't establish stable satellite connections, either onboard aircraft or walking on the street, about 80% of the time. There are not a lot of buildings around and they are not separated from each other. I have traveled around the world. The utility app on the phone needs to be opened to get position for the map. My colleague bought a similar device on the aircraft, which worked just fine, but it was not connected to the iPad. I put the left side of my helmet upside down almost every time I flew, because I didn't like the idea of it being upside down. We have the same version of the software, connection to pad devices worked fine, but mine took forever to establish satellites connection, no matter how I tried. This is a result of the comments. The one without cable is mine. I kept trying more and more and decided to come back and leave something here, but I don't know how deep the hole will be.

👤The XGPS160 track logs are not always up to date, and they have gaps of a couple of seconds with no position reports. The track logs did not have these gaps. I had to manually connect the XGPS160 to the phone each time. When the view to the southern sky was blocked by steep hillsides, the GLO was more accurate. The view to the WAAS satellites may have been partially or fully blocked. Maybe the GLO handles that situation better. The two devices had the same accuracy on the flats where the southern sky was not blocked. I used the XGPS160 logging mode with no connection to the iPhone to compare, but I used the GLO to record tracks. I drove through the Santa Cruz Mountains and the San Francisco Bay Area on the same routes. The tracks from the two devices were very close to the southern sky. When the southern sky was not visible, the GLO tracks were more close to each other and to the location of the roads. The XGPS160 tracks were close to the ground. The dual XGPS status tool is a nice utility, but it has some rough edges, like the fact that it never reported that the WAAS satellites were in use, even though the comparison with GLO suggested they were indeed being used by the XGPS160. The Trips page often has multiple tracks listed.

2. GlobalSat ND 105C Micro USB Receiver

GlobalSat ND 105C Micro USB Receiver

The chip tracking sensitivity is - 165 dBm. The time to first fix is very fast. The interface is small. There is a built-in gps antenna. A built-in battery. The Microusb toUSB cable is for use with Windows and Mac laptops. It's suitable for portable application. Very low power consumption. It supports NMEA0183 V4. SBAS, EGNOS, GAGAN, QZSS are supported. Requires a "PL2303GPSInfo" app for the phone to function. It is compatible with operating systems: Windows,Vista, 7, 8 & 10; Mac, OSX, and Linux. This is a device for navigation. It's not compatible with most navigation software. It requires a 3rd party tool to convert to a "GPS Sensor". Please read the item description.

Brand: Globalsat

👤I picked up the new Fire tablet from Amazon hoping to use the non-Amazon Store apps. It was easy to do, so I downloaded the two navigation apps. When I received the GlobalSAT unit, I plugged it into my Fire tablet and started the TomTom GO service. I drew up a route around my condo. I used it to and from work today. I can't wait to use it on a long trip. My Honda Civic doesn't have navigation in the dash, but it's $85. I now have almost all of the features of an expensive navigation system at a fraction of the price. Music, gps, weather, video, even the internet are now just arm's reach away on my dash. I'm happy! You may need to install the "You Are HereGPS" app and run it in the background while using your navigation app.

👤The last year and a half has seen the use of the gps module to navigate ocean routes. The laptop has 2G of RAM and a 32G SSD. The program is called Coastal Navigator. The laptop's processor is an Intel N series, which is slow but still fast, and draws less power than other Intel N series chips. The laptop can be connected to the gps with a 8 inchusb to microusb. The screen has an upper right margin. The module is very accurate. The signal strength of the satellites above deck was found to be marginally higher. The deck of the boat is not as important as the cloud layer and humidity. I recommend letting the boat warm up while it is being prepared for sailing. The gps is ready to navigate when the speed over ground drops. Just as accurate as a large postage stamp. I would recommend carrying a spare if you have any problems with the gps device. Why not for just $30? I only use the sounder gps for looking for a sandy spot to anchor. Want a bigger screen? You can just buy a bigger laptop. The total cost of the package is $500. A dedicated unit and a 14-inch screen cost 5000 dollars. The Cockpit Repeaters are connected to the internet. The laptop is free to move about the boat if the gps is attached to it. The gps system is easier to use with a wireless mouse. The best laptops to use would be the ones with low cost and long battery life. The original device is still working just fine, 8/11/2020, just received another one as a backup, as the gps connection has recently failed. Something is wrong with the most recent Win10 update. I was very pleased to relay new information on the improved ND-105CGPS module. It took an hour or more to reach a low.01 knot speed over ground. The new unit was at.01 knot in 3 minutes. Quite an improvement!

👤I bought this to use with aviation navigation software on my Windows 8.1 tablets and it has worked great so far. Acquisition time is very short, and WAAS is enabled by default on the chip. This doesn't use the Windows 8 location API, but instead creates a COM port for an app to access location, which should be fine for most unless your app is newer and designed to only use the Win 8 API. In that case, there are a couple different software options available from other vendors that will send the data to the location API. Only one app can access the COM port at a time. I'm able to get a full WAAS signal in my house and car, and it seems to be very sensitive. I haven't tried it in the plane yet, but I think it will work. I noticed that if there is no power at all to the microusb port, the gps will continue to run, so if you have a sleep mode, it may or may not turn the port/GPS off to save battery power. I used this in the plane and it worked better than the handheld aviation gps that I own. I had a unit on my kneeboard where it was somewhat down low and not as good of a view of the sky, but it never had an issue with satellite reception. I don't need to worry about having an antenna on top of the panel. The little gps has been an awesome value so far.

3. Navigation Glonass Stratux 10 Raspberry

Navigation Glonass Stratux 10 Raspberry

The VK-172 is a gps module that can be used for Windows and Linux. The productGPS protocol data is the default output of Vk 172 g-mouse. You can modify switch PS / GLONASS protocol data with the help of the software or serial commands. Put this module into a linux machine. No configuration or additional drivers are required. The User Manual can be found if you install the driver first. This listing page has a Technical Specification on it. If you need driver links or videos for VK-172, please contact them. How to contact us? Click "Ask a question" in the new page if you want to email them. If you need driver links or videos for VK-172, please contact them. How to contact us? Click "Ask a question" in the new page if you want to email them.

Brand: Stemedu

👤I want to get out of the way that I'm not an expert and just use this for accurate time, location, and messing around occasionally. This module has performed very well in my testing. You can't really complain about it. My first lock took about 5 minutes, but the first one didn't take long at all. The module seems to work if it's connected to a power source. When you see a green light, you know you have a lock. The quality of that lock can be very good, but you should at least have 2 satellites locked up. After I downloaded the software and driver from the U-Blox website, I plugged the gps receiver in with a cable and set it next to a window, I decided to try it on my Windows 8.1 PC. I saw a flashing light on the gps receiver and a few satellites were locked on in the software after 5 minutes. I had 7 satellites locked and 10 that were being heard. There was a small drift in speed, altitude, and latitude/longitude, but that's to be expected in modern cell phoneGPS receivers. That's a pretty good price for a cheap little device. I think I'll have better luck outside, because that was indoors. I plugged it into the device I was going to use it with, the Raspberry Pi 4 being used as an amateur radio field computer. I got a lock and an accurate grid locator when I plugged it in and configured it correctly, which is what I wanted since the Pi doesn't keep time by itself unless you use an RTC. The receiver looks pretty nice, and works exactly as it should. It can't be beaten for fifteen bucks. I'll probably end up buying more in the future because it works very well. 10/10

👤I needed a reliable time source for the ham radio digital programs and this was recommended to me. If you download the recommended software on this page, it may interfere with the software that is needed to update the computer time. I use a timer. There are many others available. I ordered a second extension cable for my other computer and it was very pleased. 73, WB4GUD.

👤A gps dongle? I was skeptical because most of the antennas are 6 to 36 inches long. I plugged it into the mt PC and after it loaded the appropriate driver, I started to see the gps data. That is boring. What about a computer? Check the video. It is too easy. Make sure your copy of Raspbian is current. To verify the TTY assigned to the dongle, open a terminal window and use apt-get install minicom. Then you have minicom -b 115200 -o -d. You have a device. What could you do with it? You can put it in your kid's trunk to see where they go. It's a good idea to put it in the sales rep's car to see if they actually visit the customer. Before you do that, check the laws of your state.

4. Humminbird Precision Receiver Heading Sensor

Humminbird Precision Receiver Heading Sensor

All of the following models are compatible with the ASGPS NMEA adapter: SOLIX, HELIX, HELIX 10, HELIX 9, HELIX 8, HELIX 7 G2N, and G3N. HD DI combo, 959ci. HD XD combo, 1159ci HD combo, 1159ci HD DI combo, 1199ci HD SI combo. The receiver has a 3.25" diameter, 1.5" high and comes with 20' cable and a stem with a 14 thread count. The compatible Humminbird product requires software that is at least 6.570. The ASGPS NMEA cable is required for connection to SOLIX and ONIX Series. The ASGPS is required by APEX. InterLink will not work with this gps receiver. It is 1.5 inch high and comes with 20' cable. Fast position fixes are accurate within 2.5 meters.

Brand: Humminbird

👤I bought this unit to make my Solix 12 position information more accurate. It was mounted on a Ram D VHF antenna mount, which was perfect for my bass boat. There were no interference problems. I am using it to map the bottom of a historically significant bay. It allows me to run a parallel track with close spacing to make sure my DI and SI collections are fully covered.

👤Works as advertised. I put my Helix 12 SI up front. I now have a stationary heading indicator. The online video shows you how to program your Helix to use the external sensor instead of the internal one.

👤I mounted this unit on the rear deck. The chart is easy to navigate, and I am certain that the craft is going in a certain direction. It is worth owning. The only way to get there is with an antenna. I secured mine to the rear deck with a simple method. The satellites are able to see the antenna from several hundred miles above you. They can see over your shoulder.

👤I use my Helix 7 on my trolly motor to keep my heading on point.

👤Before drilling holes, be sure to try out the install location on your boat. The unit has a magnetic compass, so any motor, speaker or magnet will throw it off.

👤The accuracy is increased to within a few feet.

👤I have mounted this on my Polaris Ranger for ice fishing and will purchase a second for my boat. I was hoping for better accuracy in the gps, heading sensor, and speed areas.

👤Happy husband, happy wife, happy life? It was a good purchase. It is what it says it is. If you use Graphs to find the fish, you need one.

👤The product is authentic. Excellent price.

5. HiLetgo G Mouse GLONASS Receiver Windows

HiLetgo G Mouse GLONASS Receiver Windows

There is a gps receiver for windows 10. There is a gps receiver called the g-mose. Windows 10,Vista/XP/CE are supported. The reference coordinate system is called the WGS. Tracking sensitivity is.

Brand: Hiletgo

👤It works on Windows 10 and the Pi. It will take some time and technical ability to get it going. It is not possible to use gisnass with gps/waas simultaneously. It's limited use for most. Don't abuse build quality, you will be fine. --- The review is for technical users. Instructions, software, drivers, etc. are not included in the VK172. It uses the u-blox 7020 chip and outputs a stream of standard messages. Special configuration messages can be sent/received without the software, but it's not as easy. I used Windows 10 for initial testing. It was assigned a serial comm port after plugging it in. It depends on what drivers you already have installed. I used PuTTY terminal software to connect to it after using device manager to find the correct comm port number. It showed the sentences immediately, even though the baud rate was set to a different standard. I downloaded the UBLOX "u-center for windows" software to see if it worked. Within a few minutes, I had a lock on my position and the blue led started to flash. This was not near windows. After a while, it picked up a signal from the WAAS and was receiving satellites. I felt the device was barely warm after 20 minutes. I tested it with a real time gps mode and it worked just fine. It took nearly 5 minutes to get a 3D fix after I tried it again the next morning. It may be that night time RF signals get less interference or that it didn't retain the ephemeris data. At night it was around 2 and at day it was over 3-4. When moving the receiver close to a window, two WAAS satellites were picked up. The daytimePDOP improved to 1.3-1.8. A full cold start in this location took 5 minutes and 20 seconds to get an initial fix. A hot start took less than a minute. A warm start took 31 seconds. It isn't too useful in reality because it's advertised as working with Glonass satellites. The configuration through the software seems to show that Glonass isn't enabled. The documentation states that neither gps nor qzs can be enabled. After disabling all other systems, I was able to enable Glonass. The only advantage would be if it received both at the same time. Since it doesn't, there is no point in bothering with it. I did a quick test on the Pi 3 after playing with Windows. I connected to the serial port using the putty program. I watched the expected strings. Gpsd seemed to work after a bit of effort. I looked inside. The ublox G7020-KT gps chip, ft25h03s 4Mbit serial flash, small battery like component, and patch antenna are notable components. The battery is just over 1 watt. The markings are obscured, but I think it's an XH414 which is a battery-operated device that can be used for a hot start. The soldering was good, except for the mechanical contact points which had not flowed properly, the signal pins were fine. I did not need to touch up the weak solder joints. It is a decent unit if you don't need the two things at the same time.

6. GlobalSat BU 353 S4 USB Receiver Black

GlobalSat BU 353 S4 USB Receiver Black

A built-in gps patch antenna. A built-in roof mount Magnet. 48 channels of all-in-view tracking SiRF Star IV is a gps device.

Brand: Globalsat

👤The NMEAGPS Receiver is used for applications. Does not provide location services to Windows. It was weatherized to handle all but submersion. It can be attached to many surfaces without damage. The body panels of a car are included. complies with the standards of the NMEA. The interface is a standardusb-to-serial The COM4 settings are used by the NMEA interface. There is no support for Windows location services. The device is an NMEA device. It will work in any location that works with NMEA, but no modern Windows applications. It is only IPX6 rated, meaning it is not truly waterproof. It can handle a lot of rain. Only one location update per second. This is not a 5hertz version. There's a software package that will connect to an NMEA device and create a Windows Sensor for use with location services. This is a software solution for the hardware manufacturer's lack of native software. There are some bugs. It works. The package in question is calledGPSdirect. My only problems are with the software. I know the device complies with the standards it claims to support. There are newer standards in 2015.

👤They started giving me times in 1905 after using these for a while. I get the correct date when I boot up. The receiver no longer responds and sends data after I tried to go back to the script I wrote. Until the date changes, it works well with gpsd. It works well, other than producing data that is useless. I'm not sure if we're talking about the same device. The one I have connects to a port at a rate of 5000 baud. A driver is needed to read serial data. Any application can read the data once the driver is installed, I wrote a Python script that opens the device and reads the "sentences". The first consideration is that the initial read could be a bit long. The reader has to sync with the stream, which is not difficult considering the second consideration, which is each sentence is terminated with two newline characters. When you get a full line that starts with a '$', you sync by reading. I can read the data from the receiver using "cat". The heading sentence is not generated by the receiver. The antennae is bulky, but magnetic.

👤This is my 3rd one. I use them on Windows 10 64 bit machines to do the time setting for some applications that I run. The mini-disk that comes with the puck has a utility. Your windows time is dead on if that utility is running. Turn off Windows internal time setting so they don't compete. Highly recommend the software. The program and gps ran 24x7 and the difference between Time.is and this was +0.011 seconds. I have an Amazon purchased gps repeater that is stuck on a broom handle against a window in my basement and I am seeing 7 satellites from it. The sensitivity is very good. The HDOP is 1.9 and thePDOP is 2.5. Anything below 4 is considered great.

7. GlobalSat BR 355S4 GPS Receiver Black

GlobalSat BR 355S4 GPS Receiver Black

A built-in gps patch antenna. A built-in roof mount Magnet. There is a serial port interface. Slim Profile Housing. It is compatible with most software. If you are using a laptop, you will need a cable set.

Brand: Globalsat

👤The Uniden SDS 100 works great with this, you just get the cable from Uniden, and you save $25+ compared to buying the Uniden gps kit. The radio will detect it if you connect the cable.

👤I use this to connect to my mobile radio. The radio needs aGPS to function properly when it's on the go. None of the other gps receivers worked for me. The serial gps device works for the TM-700A. I made a box that converts the 6 PIN DIn to the 5V DC that I can use to plug in a 5v DC transformer. The gps came up and locked when the radio was plugged in.

👤The Uniden rebadges is completely interchangeable with the Uniden gps puck, including the 6-pin DIN connector. It picks up a usable signal in my basement, and has good sensitivity. The data is industry standard. When searching for satellites, the LEDs blink when they get a fix. Here's the wiring diagram for the black and shield. The ground. Red is required for 50mA and Green is required for 50mA and White is required for 50mA. In, but not needed for most applications.

👤The GlobalSat BR-355S4 is the one I bought that has the PS/2 port, not the one with the plug. You need to provide a separate 5VDC power source for it to work. The attached picture shows the radio with "GPS Data OK" on it, along with the pinout information for both modules. Attach GlobalSat Pin5 TX to Uniden Yellow. Attach GlobalSat Pin1 GND to Uniden Green and a 5V ground. Attach GlobalSat Pin2 VCC to the power source and you'll get 5V across the center two conductors. There is a pinout on the internet. You probably have something in your junk drawer. Plug it into the cigarette charge and then find the two wires with 5V on them using a volt meter. You can find more information on the GlobalSat's website, but you can probably do it from the picture. You can solder wires if you can read pinout diagrams. I was very happy that this came together quickly. The radio now displays lat, lon, course and speed in knots with one button push. It was pretty slick.

👤The unit has worked well with several Icom radios. An interface cable is trivial. The unit is in the side of my house. It's easy to work with. If I needed another such unit, I would recommend and purchase again.

👤I attached this to my Uniden SDS-100 scanner and it registered 'GPS' on the screen. I had a Plug & Play installation. The reception seems to work well with this receiver.

👤Overall rating is 3 stars for erratic output and cost. The price of the bare clone modules is 3x the price of the puck and cabling. The output is not ttl, it's rs232 which is inverted and the voltage on mine is - 4.5v to + 7.7v. There is an added converter. Couldn't get a fix. There are twelve sv in view. Thenav rcvr warning is V. After being off for 12 hours, the device gets a lock and is powered up. GPRMC messages are emitted in a staccato fashion, making gps use as a clock with a seconds indicator a little troublesome. The pattern is around 1100ms, 300ms, 800, 800 and then repeating. The bare $10 gps modules are not a problem with this.

8. Hikity Android Bluetooth Receiver Support

Hikity Android Bluetooth Receiver Support

The main screen is 250(W)*145(H)mm. Installation size is 180(W)*75(H)*70(D)mm. The mirror is 2.5D. There is a RCA output/input port. Car Stereo with A2DP, support hands free call and music play. 18 preset stations can be used to search channels. There is a built-in Offline Map of North America in the gps navigation for car. You can use gps navigation at any time after connecting to the internet. This item allows to uninstall or install apps from the Application Store. The mirror link and backup camera input can be used on the following phones: When you pull the reverse gear, the device will show the rear view image automatically. Multiple functions include multi-format audio and video recoding, support for full format, brightness adjustment, Subwoofer audio output, and original steering wheel remote control. Multiple functions include multi-format audio and video recoding, support for full format, brightness adjustment, Subwoofer audio output, and original steering wheel remote control.

Brand: Hikity

👤I returned it quickly. The screen quality is good but not great. Straight garbage. Radio stations wouldn't work because they were weak. If Nav doesn't connect to the internet, it won't work because you have to download updates for the app it comes with. If it did connect, then it dropped and stopped downloads. As far as registering your commands, the touchscreen didn't work well. It's very difficult to find what you're trying to do. It's hard to do while driving. If everything worked as it was supposed to, this would be the most awesome stereo ever made. The radio is hard to use and it's a tablet. Do your research, there are probably 30 different versions of this stereo. You get what you pay for, so spend the money and get a brand name stereo like a Pioneer or a Kenwood.

👤Garbage from China is cheap. The screen isn't removed, so you can't install the dash bezel. Don't buy. You can't install dash bezel because the screen isn't removed from din. The headunit has to be left in the bin.

👤The radio experience is one of love and hate. Doesn't come with a mp3 player so you have to download it. The ones on the App Store don't keep your music in your memory. You can't pick up where you left off because Screen is not the best in bright sunlight with poor viewing angles for video. There are ghosts that affect the screen where the blues stuff is not opening.

👤Don't buy it if you just want a car stereo with a phone. If you want the backup camera. You can forget about it. There will be no picture when I back up. I've gone through every setting and taken a picture. Amazon sent me another stereo and it works the same way. I tried to get power to the camera by using both cameras. I looked at my test light. Nothing will be displayed. In the fine print, turn on structures in their barely any videos. The back up camera is not good.

👤A lot of functions were added to my '93 mustang. I am very happy with this radio and combo.

👤Spend your money on a terrible item. The item does not work as advertised. Shouldn't even have a single star here. The steering wheel controls don't work the way they're supposed to. The back-up camera works. Radio buttons work. The unit doesn't work with theusb ports.

👤The sound quality is poor.

👤It was easy to install and worth the money. The dash and installation kit have to be modified to make it fit as it is not standard dimensions. The backup camera is not bad for the price.

9. Navigation Positioning Microcontroller Compatible Sensitivity

Navigation Positioning Microcontroller Compatible Sensitivity

The phone data cable can be used directly on the computer point of view, and the default distribution of active antenna can be quickly positioned with the IPEX antenna interface. The original UBLOX 7th generation chip is used in the GT-U7 main module. The software is compatible with the GT-U7 module. The host computer-owned serial port function allows for the sending of IPX interface active antenna without the need for an external serial module. If you have a problem with their product or need product use documentation, please contact them immediately. They will be able to help you in 24 hours. They try to provide the most professional service they can.

Brand: Deegoo-fpv

👤I bought a module to use as a time reference. It gets a fix inside my house. I didn't have to change the settings on the module. I connected it to a NodeMCU controller and it worked as expected with the Tasmota NTP server. Tasmota doesn't take advantage of the signal from this module, so this configuration is not a high accuracy NTP server. That's not the fault of the module. The way Tasmota interface with the gps module is to blame. I connected it to the Pi. It worked with both and got a precise range when the PPS signal was used. The Pi 3B+ was more accurate than the Pi. It has a quad core processor and can dedicate a single core to monitoring the signal. I only tested the accuracy of the Pi's. I did not test the accuracy of the NTP clients connecting to the Pi's NTP server. The gps module was interfaced with by gpsd and Chrony under linux. The gps modules line can be accessed through the /dev/pps0 device provided by the Linux kernel. This only shows the beginning of a second, but does not show the time of day. The calender date and time can be obtained from a secondary time source. The calender date and time is provided by the gpsd daemon. I never found an advantage in configuring gpsd to access the device because Chrony can access it directly. Adding another layer to the pps and chrony is not a good idea. ppswatch is a Linux utility that shows information provided by the gps serial interface cgps, and gpsmon is a Linux utility that shows information provided by the gps module. This information was used in the setup.

👤I ordered two of them a few weeks apart. The first one worked well. I plugged the antenna into the power and dropped it onto my workbench. Within a short period of time, it had a 3D fix that would start doing 1PPS. It would get a fix a few seconds after you power it on. Incredible! I was able to use the 1PPS output for my project, even though I INRDeals I bought a second one. The second one only heard a single satellite and sat for over an hour. I switched the antennas because I thought it was a problem with the antenna. The amazing one stopped working after I got 11 satellites. The antenna was bad. There is a Even with a good antenna from the other one, it never got a fix. It is a wonder when this module works. It is useless when it goes bad. With the incredibly low price of this module, you might be able to take a chance. It seems like you'll be deeply disappointed.

10. Dual Electronics XGPS150A Multipurpose Augmentation

Dual Electronics XGPS150A Multipurpose Augmentation

Add Gps. You can strengthen your Gps signal on any device by connecting via wireless. The free downloadable app provides accurate gps coordinates, position update rate change, and much more. Being able to add accurate gps to your device will allow you to use hundreds of available apps. The Gps receiver has a battery life of over eight hours of continuous use and comes with a usb charging cord. That will stick to most surfaces.

Brand: Dual Electronics

👤It works better than I anticipated. I have an older WiFi only iPad Mini that I wanted to use for navigation but it doesn't have built-in gps. When I connected my iPad mini to the dual XGPS105A via a wireless connection, it asked to download the accompanying app. The app is useful. It tells you the number of satellites you are connected to, the signal strength, position information, and the battery status. I turned it on in the house because I couldn't wait but I was able to connect to multiple satellites with ease. I thought I would have to go outside. With the gps locked and loaded, I tried out some maps. Both worked well. My weather radar map is now location enabled. Awesome. I have taken it down the road a few times now, about 100 miles total, without issue, but I will update this review once I have a longer road trip under my belt. I didn't expect to see the app mentioned in any of the reviews or forums. This thing is special. I can't wait to try it out against other devices, like a newer iPad, windows tablets, and some surveying equipment. I will report back, but so far it's been good.

👤Don't buy anything from AXXERA or DUAL. The unit will work for 25 times, then the internals will short out, killing the battery, but they will sell you another battery. Next year there will be some other name. They changed their names to keep up with consumer fraud. Don't buy anything made by these people. You will be sad.

👤I bought a gps receiver for my Jeep. This product works in conjunction with my Apple iPad and provides pin point accurate gps for any app you are using. It takes 5 to 10 minutes to connect to my iPad via BluTooth once I turn on the puck. This could be my fault. Overall very pleased! It's easy to charge up at home or in your vehicle. Very easy to use. I stuck a piece of tape to the back of the vehicle and it still works.

👤For almost two months, use the dual XGPS150A with my iPad 2. Since the iPad 2 didn't have a gps receiver installed, I decided to use the dual XGPS 150A, which is described in the technical documentation to receive 12 gps and up. The dual XGPS15A is a free navigation app that has a very simple and minimalist design. The dual XGPS150A receiver is small and has Haptics very pleasant. The gps is green. The Bluethooth connection is created relatively fast after switch on, but the GLONASS satellites are not supported, but they are displayed in the app, but they are crossed out. It happens in dense forests on winding roads and in large cities close to tall houses. When you're on foot in New York, Boston, and Chicago, the pressure point is non-tactile, so locating is almost non-existent. The dual XGPS150A would no longer splash water and dirt if you removed the plastic cover and cut a hole in the non-slip pad.

11. GlobalSat BU 353 S4 5Hz USB Receiver Black

GlobalSat BU 353 S4 5Hz USB Receiver Black

Highly sensitive to water. 48 channels all-in-view tracking Magnet Mount is where it was built. It's suitable for use in a wide range of applications, from vehicle navigation to fire trucks, police cars, buses and much more.

Brand: Globalsat

👤The waste of $100. I have not been able to get my people to work with Win 10 or ArcMap. A waste of money. It says in the specifications that it works with Windows 10. Save yourself some money. This technology is not new. This piece of junk is not very user friendly and is far superior to my old Garmin Legend. It couldn't communicate with the test software included and I had many people that tried to get it to work on different laptops and windows tablets without success. Don't buy it!

👤I use this device to record the data of test vehicles. It seems to be of good quality. I might throw a zip tie or tape over the magnet if it's not super strong on a high speed application. The cable is long and is suitable for most driving applications. The included software was used once by me. I can't form a good opinion of it from my limited use.

👤I use a gps device for my boat. It works well.

👤It's easy to set up and use Ubuntu. When it is in view of clear sky, it will get up to 0.6m accuracy horizontally and 3m vertically. The SiRFdemo program needs to be able to manage it under windows. I have bought seven of them so far.

👤The gps puck met all of my needs. It starts fast. I use it to monitor the speed of the gps device. Very happy with the product.

👤You can use your laptop to plot your routes with a great receiver.

👤I bought this after reading that it's a reliable, if slow, gps receiver that is well supported on Linux. I'm giving up and ordering a different one from a non-Amazon vendor after spending a lot of time trying to get it to work. Every diagnostic and management tool I've used successfully opens the connection, but all attempts to swap to SiRF or NMEA fail with no error. The software that speaks both protocols can't determine if it's SiRF or NMEA, and can't read any data at all. The device has just been plugged in and the red light starts flashing, which seems suspicious since it has just been plugged in. I have come to the conclusion that my device is broken or that I received a counterfeit device. These can be found for less on other sites.

Summary

What is the best product for bu-353s4 usb gps receiver?

Bu-353s4 usb gps receiver products from Dual Electronics. In this article about bu-353s4 usb gps receiver you can see why people choose the product. Globalsat and Stemedu are also good brands to look for when you are finding bu-353s4 usb gps receiver.

What are the best brands for bu-353s4 usb gps receiver?

Dual Electronics, Globalsat and Stemedu are some of the best brands that chosen by people for bu-353s4 usb gps receiver. Find the detail in this article. Humminbird, Hiletgo and Globalsat are also brands that their products are worth to check.

You May Like

Share Your Story

Your name:
Choose product to comment:
Write your review:
By submitting this review, you are agree that:
  • Your review is based on fact, honest, polite and not harmful to anyone or any brands.
  • We have full right to show or not-to-show your review after moderation.
  • No spamm please :)
Disclaimer
We might earn comission for your shopping via our links, it doesn't cost you extra. This website is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com